Negative campaign ads just make me want to shoot all of them

Seriously, the politicking this year makes me want to just go out and kill every one of them. I’m just reaching the limits of my endurance and tolerance for my fellow-man. But there is a huge gap between want and do. So if you read about some political rally blown up with a mini nuke, I don’t have the money to buy the parts to do it. Nor the supply chain to get the parts even if I had the money. Nor the foggiest notion of where to look. So if it happens, I didn’t do it. I have been thinking about building other things, mostly.

Now what I have been thinking about when I’m not thinking about using WMD to level the political playing field has been another A-Mod build using the Predator 670cc V Twin from Harbor Freight and a “torque converter” CVT. The great thing about this is the engine and torque converter are right at 100 pounds together, and all the CVT needs to survive the 22 HP V-Twin is an upgraded aftermarket belt and adjusting the engagement speed via weights and springs. I can hang this in front of the right rear tire and move the driver left of center to balance the car and stay under the 900 pound minimum weight leaving room to ballast up and adjust the front-to-rear balance and also keep the CG low.

One thing I’m not going to do is use a steel straight tube axle. After my last post where I either calculated, actually weighed, or weighed “at the catalog” every part in the front suspension for the Sprint-T/TGS2 and discovered I had an absolutely ghastly sprung/unsprung ratio at the front end of the TGS2, I’m going for light weight over “stout” when it comes to front end bits. I’m going back to my composite days and using moldless foam core composite construction to create a flyweight straight tube or double a-arm front suspension. Now if I wasn’t concerned about banging off curbs or potholes I could make an axle you could carry with one hand and still have two or three fingers left over, unlike the 23 pound behemoth I bought for the TGS2 that takes all 5 fingers and careful handling to prevent wrist damage because of the polar moment from its 58″ length. I might do that anyway because it would be easy to make and not super expensive when compared to steel. For this build steel fabrication would be the economic benchmark, because of raw material costs and fabrication costs. And because I have the most experience recently with steel fabrication, that also makes the process my benchmark. At this point my composites experience is about 30 or more years old. I built some parts for the CVCC race car. And if you know what CVCC means you know the car would now be eligible for vintage plates.😁 And this was also the first car I bought new back in 1978…

Everything for this car would have to be built except consumables like tires, wheels, and brakes, plus brake pads. Virtually nothing could be bought “off the shelf”. Even the steering would have to be made because available boxes are too heavy and slow and rack and pinions are either heavy, slow, big or all of the above. What I envision for this build is basically a go-kart with power steering that has the pitman arm on a pivoting shaft connected directly to the steering wheel through an electric assist, with stops mounted to prevent more than about 80° motion in either direction. I see the prototype made from steel, with subsequent versions made from aluminum or composites, or a combination of materials. Get the clearances and motion paths and the places that needed more material worked out first, then build the expensive version from exotic materials, like unobtanium and noweightium. Even the chassis I’m looking at welding up the tub from sheet steel as a mockup then pulling a mold off that and building a composite tub. In fact back in the ’70s I sketched up an idea of laying up composites in a female mold, then injecting expanding foam to make a foam core and also press the laminate together and into the details of the mold, but before I could sell the idea the state of the art passed me by, making the idea interesting but ultimately useless. But getting back to that welded sheet steel tub, if it’s under the minimum weight I’m just going to leave it at that. No sense building an expensive lightweight chassis just to bolt lead in it. Or tungsten because lead is too plebian for a composite chassis. But if it’s floppy and flexible then the foam and fiberglass come out to replace the steel, because I know they are rigid from working on airplanes and other people’s completed airplanes. The process is also used on things like boats and surfboards. It was possible to buy pre-molded cores to apply your own fiberglass skin and make your own surfboard back in the day. but we kids just used the cores as floats…

And 1) I’m starting to wander about the verbal landscape and 2) I have a Shadowrun game later and I need to get up early-ish for it. so this would be a good place to call it a night…


Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.