October is somewhat early for this

But what the heck.

I’m doing a wish list of what I need to finish the Sprint-T, with markers for get it running (R), Nice to have (N), and ultimate race car (U). Now some items will cross over and get 2 or more tags (U, N, R) or (U, R) or (N, R) or (U, N) so if you want to mix and match as long as the item has at least one tag in common with other gifts it won’t be a wasted purchase. And I will also update this list with items given or purchased. So I will post a link to this post when the list gets updated.

I’m going to start the list with the tings I already have and where they fall on the list.
Body with no doors or floor (U, N, R)
Windshield posts (U, N, R)
Front axle (U, N, R)
Spindles (U, N, R)
Steering arms (U, N, R)
Steering wheel (U, N, R)
Wilwood 12.2″ disk brakes and calipers and brackets to fit spindles (U, N)
Brackets and heims for the axle (U, N, R)
Swing arms for the rear axle (U, N, R)

Now the stuff I don’t have is much longer.
Category engine:
Junkyard 5.3l LS architecture engine (R)

3.26″ stroke LS crank and matching rods from a 4.8l LS (U, N) with an aluminum block 4.0″ or larger bore (U) or a iron block from a 6.0l LS truck engine (N) a set of 862 casting number LS heads (U, N, R) and an aftermarket “Truck intake” that matches the ports on the heads (U, N, R) and this cam (U, N)

Microsquirt ECU and LS harness (U, N, R)

Category transmission:
Junkyard 4L80E transmission (U, N, R)

Junkyard 6L80E transmission (R) This one is heavier and has more loss in 1st and 2nd gears compared to the 4 speed, but gives better gas mileage highway.

Category rear end:
Junkyard 8.8″ ford axle and disk brakes in 5 X 4.5″ bolt circle (R) Found in 1983 and later Ford trucks and Ford Rangers and some Mustangs and SUVs until replaced by independent suspension. They still use the 8.8 as a center section for the independent suspension, but it won’t work for my car.

Winters or Speedway Engineering quick change with magnesium center section and aluminum tubes set up for GN or Superspeedway hubs with 1° negative camber (spindle up) and 60″ hub width (U, N)

Aluminum 5 X 4.75″ bolt circle hubs to fit the axle above (U, N) If you’re wondering the front hubs can be either Ford pattern (5 X 4.5″) or Chevy (5 X 4.75″) and the aluminum GN or Superspeedway hubs are available in 5 X 5″ or 5 X 4.75″, so they need to be the 4.75″ circle so I don’t have to buy as many kinds of wheels.

2 X 11.75″ X 0.81″ vented brake disks to fit the calipers (U, N)

Speedway emergency brake calipers Part # 91031046-L and -R and brackets BSB Manufacturing 7070 Steel Bearing Brake Floater Part # 91045534 (U, N)

That’s the current list as of 10/19/19. Watch this date to see if I update the list because I know there is stuff I left off the list of things I have, and I need much more stuff but don’t know what to get yet based on what I have and have room for in the car.


One response to “October is somewhat early for this

  1. Don’t forget the fuzzy dice.


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.